Archive:SolidRun CuBox-i: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
Line 172: | Line 172: | ||
==External Links and References== | ==External Links and References== | ||
* [http://www.solid-run.com/ Solid-Run Product Page] | * [http://www.solid-run.com/products/cubox-i-mini-computer/ Solid-Run Product Page] | ||
* [http://www.solid-run.com/community Solid-Run Community] | * [http://www.solid-run.com/community Solid-Run Community] | ||
Revision as of 13:01, 17 September 2014
Overview
Solid-Run's CuBox-i is the second generation family of mini computers, based on the SolidRun MicroSOM using scalable Freescale i.MX6 family of system-on-chip (SoC) ranging from a single to quad Cortex-A9 processor cores, 2D/3D hardware graphics processing unit, video decoding and encoding acceleration hardware, HDMI 1080p 3D broad range of peripherals.
Detailed hardware specification
CuBox-i family comparison table
CuBox-i1 | CuBox-i2 | CuBox-i2eX | CuBox-i2ultra 1 | CuBox-i4pro | |
Chipset | Solo | Dual Light | Dual | Dual | Quad |
Core Count | 1 @ 1GHz | 2 @ 1GHz | 2 @ 1GHz | 2 @ 1GHz | 4 @ 1GHz |
Memory Size | 512MByte DDR3 | 1GByte DDR3 | 1GByte DDR3 | 1GByte DDR3 | 2GByte DDR3 |
Memory Config | 32bit @ 800Mbps | 64bit @ 800Mbps | 64bit @ 1066Mbps | 64bit @ 1066Mbps | 64bit @ 1066Mbps |
3D GPU | GC880 | GC880 | GC2000 | GC2000 | GC2000 |
3D GPU Type | ES 1.1/2.0 | ES 1.1/2.0 | ES 1.1/2.0, OpenCL 1.1E | ES 1.1/2.0, OpenCL 1.1E | ES 1.1/2.0, OpenCL 1.1E |
HW Video Dec/Enc | Multiformat | Multiformat | Multiformat | Multiformat | Multiformat |
HDMI 1080p | 1.4, 3D and CEC support | 1.4, 3D and CEC support | 1.4, 3D and CEC support | 1.4, 3D and CEC support | 1.4, 3D and CEC support |
Ethernet | 10/100 Mbps | 10/100 Mbps | 10/100/1000 Mbps 2 | 10/100/1000 Mbps 2 | 10/100/1000 Mbps 2 |
WiFi 11b/g/n/BlueTooth 2.1 | Optional | Optional | Optional | v | v |
Micro SD Interface | v | v | v | v | v |
eSata II 3Gbps 3 | v | v | v | ||
RTC With Backup Battery | v | v | v | ||
Optical S/PDIF Audio Out | v | v | v | v | v |
Micro USB to RS-232 | v | v | v | ||
USB Host | 2x USB 2.0 | 2x USB 2.0 | 2x USB 2.0 | 2x USB 2.0 | 2x USB 2.0 |
InfraRed for Remote Control | 38KHz Receiver | 38KHz Receiver | 38KHz Receiver & Transmitter | 38KHz Receiver & Transmitter | 38KHz Receiver & Transmitter |
Notes:
- The CuBox-i2ultra has been replaced by the CuBox-i2eX. The only difference is that WiFi/BlueTooth is now optional
- 1000Mbps link is limited to 470Mbps actual bandwidth due to internal chip bus limitation
- With command based switching port multiplier support
Ports
Back
- Optical S/PDIF audio out
- Power connector
- Ethernet port
- HDMI port
- Micro SD card slot1
- Upper USB port
- Lower USB port
- eSATA port
- Micro USB to RS232 port
Notes
1. Install the micro-SD card so that the contacts face UP (towards the HDMI port). To ensure contact, the card must be fully inserted, with no portion extending beyond the edge of the CuBox.
Front
The front is not shown on the image. The LED and infrared receiver/transmitter are all behind the plastic window on the lower right.
- Status LED
- Infrared receiver
- Infrared transmitter
Physical Dimensions
- Approximately: 55mm x 55mm x 42mm (2.17 x 2.17 x 1.65 inches)
- Weight: Depends on the model being used