LIRC

From Official Kodi Wiki
Revision as of 18:59, 26 May 2019 by Muddysteel (talk | contribs)
Jump to navigation Jump to search
Home icon grey.png   ▶ Remote controls ▶ LIRC

LIRC (Linux Infrared Remote Control) is an open source package that allows users to receive and send infrared signals with a Linux-based computer system.

Overview of LIRC

How LIRC works with Kodi

To help understand how Kodi interacts with LIRC, consider the following scenario:

You push a button on your remote (LIRC config file lircd.conf), That button is seen by the Kodi translator (Kodi LIRC mapping file Lircmap.xml), Kodi starts the requested command (Kodi remote control mapping file remote.xml).

Let's trace it:

  • You press: KEY_GO is the actual button name on the remote in lircd.conf
  • LIRC "sees" the remote code, which is translated by the Lircmap.xml in Kodi's LIRC mapping file:
    • And maps: KEY_GO
    • Into the Kodi remote control command of: <play>
  • Finally, Kodi using the remote.xml file:
    • Takes the <play>
    • and executes the internal Play command inside of Kodi.

Whatever value is there is the REAL name of our button on the remote as defined in lircd.conf. Remember, we can map any button to any function. The actual name of the button could be STOP if we wanted to (kinda dumb but it could be) The REAL button name on the remote is NOT required to have anything to logically do with the name of the command you want to perform


Just to illustrate we called it the KEY_GO button

So to sum it up

  • Kodi sent a command (Remember we are going in reverse) called Play
  • That Play command is tied to the Lircmap.xml <play></play>
  • That Lircmap.xml <play></play> is tied to the real button on the remote that is called KEY_GO in lircd.conf


remote.xml:

<keymap>
  <global>
    <remote>
      <play>Play</play>
    </remote>
  </global>
</keymap>


Lircmap.xml:

<lircmap>
  <remote device="My-Remote-Name">		
    <play>KEY_GO</play>
  </remote>
</lircmap>


lircd.conf:

begin remote

  name  "My-Remote-Name"
  bits            5
  flags RC6|CONST_LENGTH
  eps            30
  aeps          100

  header       2662   836
  one           452   429
  zero          452   429
  pre_data_bits   32
  pre_data       0x1BFF83DF
  gap          106001
  toggle_bit_mask 0x8000
  rc6_mask    0x100000000

      begin codes
          KEY_GO             0x0F

      end codes

end remote

Installation

Generally, lirc is installed as a dependency by any system that requires it when installing Kodi.

If for whatever reason you have to install/reinstall lirc, note that the manual says systemctl should be configured to enable/start lircd.socket, and lircd.socket will start lircd.service itself. This is NOT the case if you're installing for Kodi: Kodi will open its own socket, so you should enable *only* lircd.service for it to function properly.

lircmap.xml

A custom Lircmap.xml - This file merely defines the translation, bridging a LIRC_button to a XBMC_button. The file is literally named Lircmap.xml and is stored in the userdata directory. Do not confuse the Lircmap.xml with Keyboard.xml.

LIRC_Button - what your lircd.conf calls the physical button on your remote control.

XBMC_button - an Kodi internal button title.

device name - is defined in your lircd.conf file in the "name" field.

This information can be had using the test application "irw" and then hitting some buttons. More on this in the Lirc and Lircmap.xml#Testing Lirc Output section below.

File format

Lircmap.xml format is as follows:

<lircmap>
   <remote device="devicename">
      <Kodi_button>LIRC_button</Kodi_button>
        ...
   </remote>
</lircmap>

Device name

The device name is defined in your lircd.conf file in the "name" field. This information can be had using the test application "irw" and then hitting some buttons. More on this in the Lirc and Lircmap.xml#Testing Lirc Output section below.

Kodi button names

There are two type of Kodi_buttons in Kodi.

  • Predefined Buttons are labelled using their button title such as:
  <left>
  <right>
  <title>
  <menu>

These buttons are predefined in keymap.xml and handle all functions needed for a working system. For a complete list of buttons see keymap.xml#Remote Buttons.

  • Customized buttons are for people who require more buttons than are defined by default. For example;
  <obc1>BUTTON1</obc1>
  ...
  <obc254>BUTTON254</obc254>
Note : These obc buttons must be defined in keymap.xml under the [[<universalremote>]] heading
FYI : obc stands for original button code and is a legacy of the old xbox IR remote system

Testing Lirc Output

use the command 'irw' to test your LIRC configuration

  xbmc@xbmclinux:~$ irw
  0000000000040004 00 ARROW_UP Cyp_Se_WitheHome
  0000000000040004 00 VOLUME_UP Cyp_Se_WitheHome
  0000000000040004 00 NUMPAD_6 Cyp_Se_WitheHome
  0000000000040004 00 INFO Cyp_Se_WitheHome

In this example Cyp_Se_WitheHome is the device name ARROW_UP, VOLUME_UP, NUMPAD_6, INFO are button names

If you wish to redefine the button names it can be done in /etc/lircd.conf

Examples